Project development

The reader will appreciate that the design of, for example, a large construction project from its conception, will involve technical input from architects and engineering designers in a wide variety of associated disciplines. It is vital that all contributors to the overall scheme talk the same language and that only compatible computer software packages are in use for the separate areas of work. In addition, the management contractor must have access to the designs as work is in progress.
Before the age of CAD it was the practice to have countless meetings in order to co-ordinate progress. 
Design obviously continues in steps and in planning and construction work problems arise, and designers
need to be in a position to make modifications to overcome them, before progressing to the next phase.
A typical case study illustrating the activity associated with this type of work is the construction of the new
Civil Aviation Authority ‘en-route’ centre, built at Southampton. This prestige building and installation
controls all the air traffic passing through Britain’s airspace and houses controllers operating banks of electronic and computer equipment where only an efficiency of 100% is acceptable. The building services
engineer must ensure that the environment to keep both controllers and equipment comfortable is maintained 24 hours a day, seven days a week.
Due to the extensive use of computers at the centre, a huge amount of electrical, heating, ventilating and air conditioning plant needed to be installed. Different specialist contractors were responsible for these services
under the stewardship of the management contractor.
The fast track nature of the design and construction, required an extensive application of CAD, where individual contractors responsible for electrical, mechanical and ducting work, were ‘net-worked’ on
site, and could refer to CAD data from each other. 
At this development, it was accepted by contractors that for some drawings it was practical to work in
three dimensions to make it easier, for example, to ensure clearances between piping and ductwork in the
more cramped areas. Layout drawings in 3D permitted engineers to demonstrate clearly to other parties where, for example, electrical cables and conduits were likely to plough straight through heating and ventilation ducts.
Potential problems were solved on screen rather than emerging during construction. In addition, adequate
access for maintenance purposes and replacement of equipment could be confirmed. The draughtsman can
check designs by altering the angles from which arrangements are viewed on screen.
In the design of many heavy engineering plant layouts it is often the practice to build a scale model of the
plant as design work progresses. The function of the model is to keep a running check on the feasibility of
the installation. Obvious improvements can then be incorporated.
Constructions of chemical plants and oil refineries are typical examples. After completion of the project,
models may be used for publicity purposes and to assist in the education of technicians who operate and
service the equipment. Three dimensional modelling has many other applications in the film and entertainment
industry and drawings in 3D can materially assist in comprehension. 
When many workstations have to be installed for a design team, it is vital to agree on working methods.
Recommendations for useful Standards in Construction Drawing Practice are detailed in Chapter 27.
Agreement is necessary on the organization of many aspects of work and in CAD, these include the use of
layers, the groupings of the various sections of construction designs, use of colours so that similar
ductwork appears on the screen in the same shade, procedures for the transfer of data between several
drawing offices, methods of structuring data for archiving and to help future retrieval. The quality of
all drawing work needs to be uniform and conform to BS 8888 for a complete understanding and to avoid
ambiguity. It is essential that all contributors work as a team and in harmony if planning deadlines are to be
kept, as obviously, delays in one area of construction can hold up another contractors work, and may result
in financial loss.
The designs for services and installations originate from specifications and schematic layouts, supplied
by Consulting Engineers, acting on behalf of the Clients or Agents.
For layout work a typical draughting package which covers all aspects of services, such as electrical, lighting,
communication, alarms, ductwork, sanitary and mechanical plant, is desirable and time saving. Standard
symbols can be inserted on their apropriate drawing layer, rotated automatically to align with a wall or
ceiling grid and automatically scaled so that they are plotted at the correct scale. These settings can also be
customized to enable you to predefine commonly used layers and sizes.
The Building Services Library supplied by HEVACOMP, 109 Regents Park Road, London NW1 8UR
is a typical package which covers these requirements and permits you to store up to 600 of your own symbols
using tablet or pull down menus. The package will assist in the creation of working drawings and in the
detailing of, for example, sections of ductwork, the program will prompt for the dimensions, elevation and
layer; subsequent sections of ductwork are then able to attach automatically, matching the layer and size.
Parametric routines are also used to efficiently design a wide variety of bends, tees, branches and transition
pieces for all types of square, rectangular, circular and oval ductwork.
Schedules of fittings need to be created with essential information and if necessary interfaced with other
database or spreadsheet programs, in order to prepare bills of materials.
Electrical wiring systems for lighting and services must be designed in accordance with I.E.E. Wiring Regulations and programs are available to provide the essential requirements of both the electrical designer
and contractor.
The ELEC program from HEVACOMP can be used to calculate all cable, cpc and fuse sizes, as well as
voltage drops, earth fault loop impedances, and short circuit currents. Schematic diagrams are easily prepared
up to AO in size, showing load descriptions, protective device and cable sizes as well as sub-main details.
Reporting facilities include:
Board and way data,
Cable sizes and voltage drops,
Short circuit currents and disconnection times,
Discrimination charts,
Input data,
Calculation file data,
Load current summary,
Voltage drop summary,
Equipment schedules.





Manual of
Engineering Drawing
Second edition
Colin H Simmons
I.Eng, FIED, Mem ASME.
Engineering Standards Consultant
Member of BS. & ISO Committees dealing with
Technical Product Documentation specifications
Formerly Standards Engineer, Lucas CAV.
Dennis E Maguire
CEng. MIMechE, Mem ASME, R.Eng.Des, MIED
Design Consultant
Formerly Senior Lecturer, Mechanical and
Production Engineering Department, Southall College
of Technology
City & Guilds International Chief Examiner in
Engineering Drawing





for more details and updates about photoshop simple tutorial please visit.........
www.photoshopsimpletutorial.blogspot.com

---or---



  • www.photoshop-simple-tutorial.com
  • 1 comment:

    1. Kami www.desain3d.com menawarkan Jasa desain untuk desain cafe bambu, desain cafe tenda, desain cafe minimalis,
      cafe interior design, cafe logo design, cafe kitchen design yang berpengalaman dan terpercaya.
      Kami menawarkan jasa mendesain segala bangunan Interior dan eksterior secara online
      Kami, siap membantu anda untuk mewujudkan desain yang anda inginkan dengan cepat dengan harga relatif murah, tanpa perlu bertatap muka, tanpa perlu bertemu langsung.
      disini kami menyediakan jasa desain interior untuk rumah tinggal, apartemen, kantor, dan stand pameran.juga menerima berbagai macam desain, mulai dari desain bangunan, gambar-gambar desain produk, desain packaging, jasa gambar autocad 2D & 3D solidworks, jasa drafter drawing CAD 2D dan desain 3D Solidworks,Jasa pembuatan gambar kerja, Jasa pembuatan gambar detail, Revisi segala macam drawing produk, Autocad Drafter, Jasa drafter, Jasa Gambar Rumah Desain Bangunan AutoCAD 2D Solidworks 3D modeling gambar kerja design arsitek teknik sipil mesin Building Designer bangunan jalan listrik elektro denah paving blok gudang Object skema layout Perspektif 3D gambar kerja detail CAD drafter hotel gedung konstruksi permesinan engineering Proyek Kontraktor Reviews perancangan design product desain produk mekanik manufaktur drafting Packaging furniture konstruksi area taman parkir.

      Cukup dengan SMS ke 081916200296, 08979198363, Email ke arusha.st@atau BBM, desain yang anda butuhkan sudah sesuai keinginan anda.

      Jasa desain murah
      www.jasa-gambar-desain.blogspot.com
      www.jasa-desain-gambar-murah.blogspot.com
      www.autocad-solidworks-unigraphics.blogspot.com
      www.jasa-interior-eksterior3d.blogspot.com
      www.jasa-desain-rumah-autocad.blogspot.com
      www.jasa-desainer.blogspot.com

      Bagi anda yang ingin memperdalam ilmu desain silahkan kunjungin blog kita yang gratis, simple dan cepat.
      belajar autocad
      www.autocadline.blogspot.com
      belajar solidworks
      www.solidworksurface.blogspot.com
      belajar desain
      www.spotcolordesign.blogspot.com
      belajar illustrator
      www.illustratorgradient.blogspot.com
      belajar photoshop
      www.photoshoptonality.blogspot.com

      Belajar 2D 3D tutorial
      www.all-design-tutorial.blogspot.com

      solidworks tutorial
      www.solidworkengineering.blogspot.com
      www.solidworkforever.blogspot.com
      www.solidworkmydesign.blogspot.com
      www.solidworkbloggers.blogspot.com
      unigraphics tutorial
      www.arsala34.blogspot.com
      www.unigraphicsmydesign.blogspot.com
      www.unigraphicsforever.blogspot.com
      www.unigraphicsengineering.blogspot.com
      www.unigraphicsbloggers.blogspot.com
      autocad tutorial
      www.autocadforever.blogspot.com
      www.autocadengineering.blogspot.com
      www.autocadbloggers.blogspot.com
      illustrator tutorial
      www.illustratorforever.blogspot.com
      www.illustratorbloggers.blogspot.com
      www.graphicsdesignsimple.blogspot.com
      www.photoshopbloggers.blogspot.com
      www.imeulia1.blogspot.com
      Product design
      www.product-engineering-design.blogspot.com
      www.imeulia.blogspot.com
      www.engineeringdesignart.blogspot.com
      www.mechanicalengineeringart.blogspot.com
      www.materials-engineeringscience.blogspot.com
      www.stainless-steels-volume1.blogspot.com
      www.alumunium-alloys.blogspot.com
      www.computerengineeringdesign.blogspot.com
      www.plasticmanufacturers.blogspot.com
      www.injectionmoldingdesign.blogspot.com
      www.blowmoldingdesign.blogspot.com
      www.producthesis.blogspot.com
      www.arsyananda-desain.blogspot.com
      www.materialselection.blogspot.com
      www.engineeringdesignsimple.blogspot.com
      www.smart-materials.blogspot.com
      www.imeulia2.blogspot.com
      www.automotivematic.blogspot.com
      www.automotivemachine.blogspot.com

      Untuk yang ingin belajar lebih lengkap, step by step dan lebih detail kunjungi :

      www.autocadsimpletutorial.blogspot.com
      www.solidworksimpletutorial.blogspot.com
      www.unigraphicsimpletutorial.blogspot.com
      www.illustratorsimpletutorial.blogspot.com
      www.photoshopsimpletutorial.blogspot.com

      ReplyDelete